Online Questions - Valid Practice To your Hybrid-Cloud-Observability-Network-Monitoring Exam (Updated 153 Questions)
Practice To Hybrid-Cloud-Observability-Network-Monitoring - Remarkable Practice On your Hybrid Cloud Observability Network Monitoring Exam Exam
NEW QUESTION # 58
How is an object ID (OID) verified as included in SolarWinds' MIB database and polled on a device?
- A. go to manage pollers and find OID
- B. run SNMPwalk on the device with the OID
- C. verify the OID using the MIB browser
- D. add routers to the additional polling engine
Answer: C
NEW QUESTION # 59
When attempting to add universal device poller (UDP) results to a new chart widget, none of the custom poller results are displayed. If the web console switches to another view, the data appears in the chart. What is the most likely resolution?
- A. unassign and reassign custom poller in UDP application
- B. UDP application under web display, chart box must be checked for each view to be used
- C. user does not have correct permissions to view the data
- D. UDP application, click transform results to convert them into a format viewable in a chart
Answer: B
NEW QUESTION # 60
What is the unit of data used for alerting on flows?
- A. gps
- B. bPs
- C. mbps
- D. ms
Answer: B
NEW QUESTION # 61
Which three of the following steps should be taken to troubleshoot a 'test failed' result for SNMP nodes in hybrid cloud observability? (Choose three.)
- A. Add remote site node and confirm firewall rules are configured to allow SNMP traffic.
- B. Verify the node can be pinged from the application server.
- C. Verify the SNMP service on the node has been restarted after changing the community string.
- D. Confirm the use ofSNMPv3 with authentication keys.
Answer: A,B,C
NEW QUESTION # 62
Which three of the following switch port report errors can cause a duplex mismatch? (Choose three.)
- A. 100 MB full
- B. > 0.5% receive
- C. CRC
- D. are collision
Answer: B,C,D
NEW QUESTION # 63
A new node has been added to hybrid cloud observability; however, certain data being polled on similar devices is not being polled on the new node. How can this be resolved?
- A. assign the new node to the same polling engine
- B. assign existinguniversal device poller (UDP) to new node
- C. UDP must be re-created for new node
- D. verily the credentials for the new node are valid
Answer: B
NEW QUESTION # 64
If the data collected for hardware health is incorrect, which step could rectify the issue?
- A. Change the poller assigned to sensor.
- B. Create a custom goller in device studio for fan speed, power supply, and temperature.
- C. Change the MIB tree used for polling.
- D. Download the MIB file from the SolarWinds website and add it to the device's firmware.
Answer: C
NEW QUESTION # 65
Which two of the following flow sources are supported by hybrid cloud observability? (Choose two.)
- A. cFlow
- B. NetStream
- C. J-Flow
- D. Cisco
Answer: C,D
NEW QUESTION # 66
A device studio poller is being built for the node details widget. The plan is to add a field for serial numbers.
How would this be accomplished?
- A. Create a serial number universal device poller (UDP) and link to the node details widget.
- B. Add the object ID (QID) to an existing data source and edit the field name in the widget.
- C. Change one data source field to serial number and supply the OID for the data source.
- D. Default widgets are being used, fields cannot be added to the device studio
Answer: A
NEW QUESTION # 67
Which two of the following technologies does device studio support? (Choose two.)
- A. |multi-CPU and memory
- B. baseline and thresholds
- C. node details
- D. throughput
Answer: A,C
NEW QUESTION # 68
Which Cisco IOS feature is enabled to pinpoint an application causing slow network performance?
- A. IPSLA
- B. SNMP
- C. Net Flow
- D. SPAN
Answer: C
NEW QUESTION # 69
Which three of the following data points does NetFlow use to confirm traffic is in the same flow? (Choose three.)
- A. port number
- B. interface name
- C. L3 protocol
- D. IP address
Answer: A,C,D
NEW QUESTION # 70
On a single node, one or more interfaces are showing an "unknown" status. What is the best way to resolve the issue?
- A. Verify the interfaces are assigned to SolarWinds' native poller.
- B. Delete and rediscover the node showing affected interfaces.
- C. Change node's pollingmethod to ICMP.
- D. Delete and re-add the affected interfaces.
Answer: D
NEW QUESTION # 71
One NetPath probe is showing a "no data found" error, however other probes are returning data without issue.
What is the most likely resolution?
- A. add the probe ID to the engines table manually
- B. delete the probe, reinstall the agent manually, and re-add the probe
- C. probe was added in NetPath without an agent installed on its node
- D. restart the SolarWinds agent service on the node
Answer: B
NEW QUESTION # 72
A problem occurred on the main polling engine and the server fails. It is noted that statistics for the networking devices polled by a universal device poller (UDP) custom monitor are missing. Which two of the following reasons are possible causes of this event? (Choose two.)
- A. data collection for any UDPs stops on the server
- B. UDPs do not collect data from failover or hot standby engines
- C. UDPs are tied to the polling engine on which they are hosted
- D. networking devices are not assigned to the UDP
Answer: A,C
NEW QUESTION # 73
Which status rollup mode displays groups defined as collections of redundant or backup devices?
- A. showzero
- B. show best
- C. show worst
- D. show mixed
Answer: B
NEW QUESTION # 74
Which two of the following services can be monitored in network insight with network health, performance monitor, and NCM features installed in hybrid cloud observability? (Choose two.)
- A. global protect VPN
- B. policy details
- C. high availability details
- D. access lists
Answer: A,C
NEW QUESTION # 75
Which custom poller supports multiple object IDs (OIDs)?
- A. device studio
- B. universal device poller (UDP)
- C. component monitor
- D. hardware health
Answer: B
NEW QUESTION # 76
When a parent object goes down or becomes unresponsive, all interfaces on the switch will also be unresponsive. Though they may be working, "unreachable" status is used because the parent node reports as
"down" and a status cannot be determined. Any alerts where the trigger condition includes node status equal to
"down" are not triggered.
In which section of SolarWinds' platform can an administrator configure the status of child objects as
"unreachable" instead of "down" or "unknown"?
- A. core thresholds
- B. manage dependencies
- C. node status participation
- D. polling settings
Answer: B
NEW QUESTION # 77
Which two of the following actions can be taken to resolve duplicate flows? (Choose two.)
- A. Enable automatic addition of flow sources.
- B. Ensure NetFlow is enabled for ingress interfaces.
- C. Enable the flow de-duplication feature.
- D. Ensure NetFlow export is enabled on sub-interfaces.
Answer: B,C
NEW QUESTION # 78
What can be done to show the description of an object ID (OID)?
- A. Perform an SNMPwalk on the tarqet device.
- B. Download the latest OlD.cfq from customer portal.
- C. Contact vendor to obtain the latest SNMPwalk.
- D. Update the MIB database via SolarWinds support.
Answer: A
NEW QUESTION # 79
......
True Hybrid-Cloud-Observability-Network-Monitoring Exam Extraordinary Practice For the Exam: https://www.dumpsvalid.com/Hybrid-Cloud-Observability-Network-Monitoring-still-valid-exam.html
Get 100% Passing Success With True Hybrid-Cloud-Observability-Network-Monitoring Exam: https://drive.google.com/open?id=1IRYlb1O1Y-uD7l25gyE8mS2mV1Y1q_4q