Cisco 300-510 Certification Exam Dumps with 104 Practice Test Questions
New 300-510 Exam Dumps with High Passing Rate
NEW QUESTION 24 
Refer to the exhibit. Which effect of this configuration is true?
- A. It sets the hold timer to 30 milliseconds and the keepalive timer to 240 milliseconds
- B. It sets the keepalive timer to 30 seconds and the hold timer to 240 seconds.
- C. It sets the keepalive timer to 30 milliseconds and the hold timer to 240 milliseconds
- D. It sets the hold timer to 30 seconds and the keepalive timer to 240 seconds
Answer: B
Explanation:
Explanation
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_bgp/command/irg-cr-book/bgp-s1.html#wp1552800140
NEW QUESTION 25
Refer to the exhibit.
After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?
- A. Router 2 receives a Type 7 LSAs from router 3 for its connected subnets
- B. Router 2 uses router 1 as the next hop for 192.168.0.0/24
- C. Router 2 uses router 3 as the next hop for 192.168.0.0/24
- D. Router 2 receives a Type 5 LSAs from router 1 for its connected subnets
Answer: D
NEW QUESTION 26
Refer to the exhibit.
After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?
- A. The two routers have the same network ID.
- B. The two routers have different IS-types.
- C. The two routers have the same area ID.
- D. The two routers cannot authenticate with one another.
Answer: D
NEW QUESTION 27
Refer to the exhibit.
Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?
- A. Router 2 must have a tunnel interface created with router 1 as the destination
- B. Router 1 must define an explicit path to router 2
- C. Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1
- D. Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces
Answer: C
NEW QUESTION 28
Refer to the exhibit.
An engineer is addressing an IS-IS design issue which is running within the topology. All links are running on FastEthernet, except the link between R5 and R4, which is Gigabit Ethernet. Which statement about the design is true?
- A. All links have equal cost if the default metric is used
- B. R1 prefer to use R5 as the next hop to reach R4
- C. R5 prefers to use R4 as the next hop for all routes
- D. R4 prefer to reach R5 using R1 as the next hop
Answer: A
NEW QUESTION 29
Refer to the exhibit.
An engineer has successfully fixed BGP peering issue. R1 has an established eBGP peering with R2 and R3. Which mechanism should the engineer apply in order to steer the traffic correctly?
- A. The weight attribute can be applied on R2 to influence AS 65513 to use AS 65515 as the primary path.
- B. The MED attribute can be applied on R2 to influence R1 to use it as the primary path.
- C. The local preference attribute can be applied on R3 to influence AS 65513 to use AS 65515 as the secondary path.
- D. The IGP metric can be manipulated on R1 to allow traffic to be load balanced between R2 and R3.
Answer: D
NEW QUESTION 30
Refer to the exhibit.
A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate. Which configuration change ensures that only the aggregate is announced now and in the future if other networks are to be added?
- A. Set each specific route in the AGGRO policy to drop instead of suppress-route
- B. Set each specific route in the AGGRO policy to remove instead of suppress-route
- C. Configure the summary-only keyword on the aggregate command
- D. Filter the routes on the receiving router
Answer: C
NEW QUESTION 31
Refer to the exhibit.
A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate. Which configuration change ensures that only the aggregate is announced now and in the future if other networks are to be added?
- A. Set each specific route in the AGGRO policy to drop instead of suppress-route
- B. Set each specific route in the AGGRO policy to remove instead of suppress-route
- C. Configure the summary-only keyword on the aggregate command
- D. Filter the routes on the receiving router
Answer: C
NEW QUESTION 32
A network consultant is troubleshooting IS-IS instances to identify why a routing domains is having communication problems between the two instances. Which description of the possible cause of issues in the routing domain is true?
- A. The configured IS-IS NSEL value is not allowing the routing systems to establish a neighborship
- B. The interface mode ip router is-is command was not included in the script
- C. The IS-IS "ISP" and "ISP2" instances are unrelated and unable to intercommunicate
- D. The same interface cannot be advertised in two different IS-IS instances
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_isis/configuration/xe-3s/irs-xe-3s-book/ irs-instance-vrf.html
NEW QUESTION 33
Refer to the exhibit.
A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology. Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: D
NEW QUESTION 34
Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware?
- A. ipv4 pim bidir-enable
- B. ip multicast-routing
- C. ip pim bidir
- D. ip pim bidir-enable
Answer: D
Explanation:
Reference:
imc_basic_cfg.html
NEW QUESTION 35
Refer to the exhibit.
R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3 is in BGP AS 3. Assume that there is no connectivity issue between R1, R2 and R1, R3. Which result between BGP peers R1, R2 and R1, R3 is true?
- A. The BGP session comes up between R1 and R2 and between R1 and R3.
- B. The BGP session comes up between R1 and R3, but not between R1 and R2.
- C. The BGP session does not come up between R1 and R2 and between R1 and R3.
- D. The BGP session comes up between R1 and R2, but not between R1 and R3.
Answer: A
NEW QUESTION 36
Refer to the exhibit.
Router 1 is connected to router 2 on interface TenGigE0/1. Which interface provides the alternate path to 172.16.200.9/32 when the link between router 1 and router 2 goes down?
- A. TenGigE0/1 interface provides the alternate path
- B. A primary path must be manually installed
- C. TenGigE0/2 interface provides the alternate path
- D. A backup path must be statically installed
Answer: C
NEW QUESTION 37
Refer to the exhibits.
All links inside the network are configured at a default cost of one inside the fully converged OSPF domain. Given the configuration from XR1, which interface does traffic from XR1 that is destined to the loopback interface of XR6 select for the exiting interface?
- A. Interface GigabitEthernet 0/0. The tier breaker of the path cost being lower. The node index priority does not impact this selection process.
- B. Interface GigabitElhemet 0/0. The tie breaker of the node index priority is lower and trumps the path cost.
- C. Interface GigabitEthernet 0/1. The tie breaker of the path cost being lower. The node index priority does not impact this selection process.
- D. Interface GigabitEthernet 0/1. The tie breaker of the node index priority is lower and trumps the path cost.
Answer: B
NEW QUESTION 38
Refer to the exhibit.
Which LSA type is indicated by this router output?
- A. type 1 LSA
- B. type 3 LSA
- C. type 2 LSA
- D. type 4 LSA
Answer: A
NEW QUESTION 39
Refer to the exhibit.
After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?
- A. The two routers have the same network ID.
- B. The two routers have different IS-types.
- C. The two routers have the same area ID.
- D. The two routers cannot authenticate with one another.
Answer: D
NEW QUESTION 40
Refer to the exhibit.
A service provider technician is working on a multicast issue for a customer. While checking the multicast table, the technician notices that no flags are present for the (1.1.1.1, 239.1.1.1) entry, yet flags are present for the (1.1.1.1, 232.1.1.1) entry.
Which factor might explain this issue?
- A. Only ASM is permitted
- B. Only GLOP is permitted
- C. Only the administratively scoped range is permitted
- D. Only the default SSM range is permitted
Answer: D
NEW QUESTION 41
Which statement about enabling segment routing for IGPs is true?
- A. Segment routing can be enabled only globally
- B. Segment routing must first be enabled under then routing process and then globally
- C. Segment routing must first be enabled globally and then under the routing process
- D. Segment routing can be enabled only under the routing process
Answer: C
NEW QUESTION 42
Which cost is the default when redistributing routes from BGP to OSPF?
- A. infinite
- B. 0
- C. 1
- D. automatic
Answer: B
Explanation:
Reference:
http://www.ciscopress.com/articles/article.asp?p=27573
NEW QUESTION 43
Which two statements about route reflectors are true? (Choose two.)
- A. If a router received an iBGP route with the originator-ID attribute set to its own router ID, the route is discarded.
- B. Routes received from nonclient peers are reflected to route reflector clients as well as nonclient peers.
- C. Routes received from a route reflector client is reflected to other clients and nonclient peers.
- D. If a route reflector receives a route with a cluster-list attribute containing a different cluster ID, the route is discarded.
- E. Routes received from nonclient peers are reflected to route reflector cluster as well as OSPF peers.
Answer: A,C
NEW QUESTION 44
Refer to the exhibit.
A network engineer applied configuration on R5 to summarize all OSPF routes, but R4 is still receiving specific routes from R5. The engineer has confirmed that both R5 and R4 routers are configured with correct summarization configuration but R5 Is not sending the summary routes What action must the engineer take to fix the problem?
- A. Configure a sham link between R4 and R5 to support summarization within Area 2
- B. Clear link-state database on both R4 and R5 routers for summarization to work
- C. Remove summarization configuration on R5 and configure it on R4
- D. Move R4 and R5 in separate areas as now they maintain the same link-state database
Answer: D
NEW QUESTION 45
Refer to the exhibit.
Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?
- A. Router 2 must have a tunnel interface created with router 1 as the destination
- B. Router 1 must define an explicit path to router 2
- C. Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1
- D. Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces
Answer: C
NEW QUESTION 46
......
Topics of Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam
These core topics of 310-510 SPRI practice test listed below are general recommendations for the material that is likely to be used for the examination. However, on any delivery of the test, other similar topics could also appear. The guidelines below can update at any time without notice to better represent the contents of the 310-510 SPRI dumps pdf and for clarity purposes.
It is recommended that, where possible, the applicant use these courses and/or other resources to provide background information on the exam objectives. The syllabus for the Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) examination is listed below in detail for each section of 300-510 SPRI dumps:
- Implementing Interdomain IP Multicast
- Troubleshoot Routing Protocols
- Implementing Cisco MPLS Traffic Engineering
- Implement PIM-SM Enhancements
- Implement and troubleshoot MPLS traffic engineering
- Implementing PIM-SM Enhancements
- Troubleshooting Routing Protocols
- Implement Tunnels for IPv6
- Implement and verifying the PIM-SM protocol
- Implement Rendezvous Point Distribution
- Implement Route Redistribution
- Implement Cisco MPLS TE
- Implementing and Verifying Intermediate System to Intermediate System Multilevel Networks
- Enable and Optimize PIM-SM
- Influencing Border Gateway Protocol Route Selection
- Implement mechanisms for dynamic Rendezvous Point (RP) distribution
- Implement BGP Route Reflectors
- Implementing and Verifying MPLS
- Describing Segment Routing Traffic Engineering (SR-TE)
- Implement BGP security options
- Implement and verify MPLS
- Implementing IP Multicast Concepts and Technologies
- Deploying IPv6 Tunneling Mechanisms
- Troubleshoot OSPF, ISIS, and BGP
- Implement enhanced Protocol-Independent Multicast - Sparse Mode (PIM-SM) features
- Implement advanced features to improve convergence in BGP networks
- Implementing Route Redistribution
- Securing BGP in Service Provider Networks
- Implement and verify segment routing technology within an interior gateway protocol
- Implement Multicast Source Discovery Protocol (MSDP) in the interdomain environment
- Describe and compare core multicast concepts
- Describe how traffic engineering is used in segment routing networks
- Influence BGP Route Selection
- Implement IPv6 tunneling mechanisms
- Implement BGP Security Options
- Implementing and Verifying Open Shortest Path First Multiarea Networks
- Implementing Distributed Rendezvous Point Solution in Multicast Network
- Configure and Verify Interior Gateway Protocol (IGP) Segment Routing
- Introducing Routing Protocol Tools, Route Maps, and Routing Policy Language
- Scaling BGP in Service Provider Networks
- Implement OSPF Special Area Types (IPv4 and IPv6)
- Implement Multiarea IS-IS
- Implement MPLS in the Service Provider Core
- Improving BGP Convergence and Implementing Advanced Operations
- Implementing Segment Routing
- Implementing PIM-SM Protocol
Get 300-510 Braindumps & 300-510 Real Exam Questions: https://www.dumpsvalid.com/300-510-still-valid-exam.html
Cisco 300-510 Actual Questions and Braindumps: https://drive.google.com/open?id=1Pu_rvgePodR6yNzFvj2ytJ_F8Hhp567r